Safety Data Sheet

SDS - Scotts Osmocote Landscape - 220719

English 91 KB PDF Valid until 2027-07-19

Applies to Osmocote Landscape Formula | Controlled Release Fertiliser

Document contents

Text extracted from the source document for accessibility and reference. Always consult the original safety data sheet above for the authoritative version.

SAFETY DATA SHEET

Revision date: 19-Jul-2022 Revision Number 1.1

1. Identification of the Material and Supplier

Product identifier

  • Product Name: SCOTTS OSMOCOTE PLUS TRACE ELEMENTS LANDSCAPE
  • Product Code(s): 000000068010

Other means of identification

  • UN number: 2071

Recommended use of the chemical and restrictions on use

  • Recommended use: Fertiliser.
  • Uses advised against: No information available.

Supplier

  • Evergreen Garden Care Australia Pty Ltd
  • 31 003 126 162
  • Building E, Level 2, 24-32 Lexington Drive, Bella Vista, NSW, 2153, Australia
  • Telephone Number: +61 (2) 8602 9000
  • Facsimile: +61 (2) 8602 9001

Emergency telephone number

  • Emergency telephone number: (ALL HOURS)

Please ensure you refer to the limitations of this Safety Data Sheet as set out in the "Other Information" section at the end of this Data Sheet.


2. Hazards Identification

GHS Classification

Classified as dangerous goods in accordance with the Australian Code for the Transport of Explosives by Road and Rail.

Fertilisers meeting the descriptions of UN 2071 are not subject to to the provisions of the Australian Code for the Transport of Dangerous Goods by Road and Rail for transport by road. Dangerous Goods only when transported by air or sea.

Classified as a hazardous chemical in accordance with the criteria of Safe Work Australia - Globally Harmonized System (GHS).

  • Skin corrosion/irritation: Category 3
  • Serious eye damage/eye irritation: Category 2A
  • Acute aquatic toxicity: Category 2
  • Chronic aquatic toxicity: Category 2

SIGNAL WORD Warning

Label elements

  • [Exclamation mark pictogram]
  • [Environment pictogram]

Hazard statements

  • H316 - Causes mild skin irritation
  • H319 - Causes serious eye irritation
  • H411 - Toxic to aquatic life with long lasting effects

Precautionary Statements - Prevention

  • Wash hands thoroughly after handling
  • Wear protective gloves / protective clothing / eye protection / face protection
  • Avoid release to the environment

Precautionary Statements - Response

  • IF exposed:
  • IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing
  • If eye irritation persists: Get medical advice/attention
  • If skin irritation occurs: Get medical advice/attention
  • Collect spillage

Precautionary Statements - Storage

  • No storage statements

Precautionary Statements - Disposal

  • Dispose of contents/container in accordance with local, regional, national, and international regulations as applicable

Other hazards which do not result in classification

  • Poisons Schedule (SUSMP): None allocated

3. Composition/information on Ingredients

Chemical name CAS No. Weight-%
Ammonium nitrate 6484-52-2 10-<30%
Magnesium oxide -4 1-<10%
Sulfur 7704-34-9 1-<10%
Copper (II) sulfate 7758-98-7 <1%
Other component(s) - to 100%

4. First Aid Measures

Description of first aid measures

  • General advice: For advice, contact a Poisons Information Centre (e.g. phone Australia 13 11 26; New Zealand 0800 764 766) or a doctor.
  • Inhalation: Remove to fresh air and keep at rest in a position comfortable for breathing. If exposed or concerned: Get medical advice/attention.
  • Eye contact: Rinse thoroughly with plenty of water for at least 15 minutes, lifting lower and upper eyelids. Consult a physician.
  • Skin contact: Wash off immediately with soap and plenty of water. Get medical attention if irritation develops and persists.
  • Ingestion: Rinse mouth thoroughly with water. Drink 1 or 2 glasses of water. Do NOT induce vomiting. Get medical attention.

Most important symptoms and effects, both acute and delayed

  • Symptoms: No information available.

Indication of any immediate medical attention and special treatment needed

  • Note to physicians: Treat symptomatically.

5. Fire Fighting Measures

Suitable Extinguishing Media

  • Suitable Extinguishing Media: Coarse water spray, Dry chemical, CO2, sand, earth, water spray or regular foam.
  • Unsuitable extinguishing media: No information available.

Specific hazards arising from the chemical

  • Specific hazards arising from the chemical: Combustible solid. Environmentally hazardous. Thermal decomposition can lead to release of irritating and toxic gases and vapors.
  • Hazardous combustion products: Carbon oxides. Nitrogen oxides. Ammonium nitrate fumes.

Special protective actions for fire-fighters

  • Special protective equipment for fire-fighters: Firefighters should wear self-contained breathing apparatus and full firefighting turnout gear. Use personal protection equipment.
  • Hazchem code: 1Z

6. Accidental Release Measures

Personal precautions, protective equipment and emergency procedures

  • Personal precautions: Avoid contact with skin, eyes, and clothing. Avoid breathing dust or spray mist. Avoid generation of dust. Use personal protective equipment as required.
  • Other information: Refer to protective measures listed in Sections 7 and 8.
  • For emergency responders: Shut off ignition sources. Use personal protection recommended in Section 8.

Environmental precautions

  • Environmental precautions: See Section 12 for additional Ecological Information.

Methods and material for containment and cleaning up

  • Methods for containment: Remove ignition sources. Provide adequate ventilation. Prevent further leakage or spillage if safe to do so. Prevent dust cloud. Cover with plastic sheet to prevent spreading.
  • Methods for cleaning up: Cover with damp absorbent (inert material, sand or soil). Use appropriate personal protective equipment (PPE). Carefully shovel or sweep up spilled material and place in suitable container. Avoid generating dust. Prevent product and washings from entering drains, sewers or surface water due to high toxicity to aquatic organisms.

7. Handling and Storage

Precautions for safe handling

  • Advice on safe handling: Handle in accordance with good industrial hygiene and safety practice. Avoid contact with skin, eyes, and clothing. Avoid generation of dust.
  • General hygiene considerations: Avoid contact with skin, eyes, and clothing. Wear suitable gloves and eye/face protection. Do not eat, drink or smoke when using this product.

Conditions for safe storage, including any incompatibilities

  • Storage Conditions: Keep containers tightly closed in a dry, cool and well-ventilated place. Store away from sources of heat or ignition.
  • Incompatible materials: Strong oxidizing agents.
  • Poisons Schedule (SUSMP): None allocated

8. Exposure Controls/personal Protection

Control parameters

  • Exposure Limits: No value assigned for this specific material by Safe Work Australia. However, Workplace Exposure Standard(s) for constituent(s):
Chemical name Australia ACGIH TLV
Copper (II) sulfate
7758-98-7
- TWA: 1 $mg/m^3$ Cu dust and mist

Magnesium oxide (fume): 8hr TWA = 10 $mg/m^3$ Dusts not otherwise classified: 8hr TWA = 10 $mg/m^3$

As published by Safe Work Australia Workplace Exposure Standards for Airborne Contaminants.

TWA - The time-weighted average airborne concentration of a particular substance when calculated over an eight-hour working day, for a five-day working week.

These Workplace Exposure Standards are guides to be used in the control of occupational health hazards. All atmospheric contamination should be kept to as low a level as is workable. These workplace exposure standards should not be used as fine dividing lines between safe and dangerous concentrations of chemicals. They are not a measure of relative toxicity.

Appropriate engineering controls

  • Engineering controls: Apply technical measures to comply with the occupational exposure limits.

If in the handling and application of this material, safe exposure levels could be exceeded, the use of engineering controls such as local exhaust ventilation must be considered and the results documented. If achieving safe exposure levels does not require engineering controls, then a detailed and documented risk assessment using the relevant Personal Protective Equipment (PPE) (refer to PPE section below) as a basis must be carried out to determine the minimum PPE requirements.

Individual protection measures, such as personal protective equipment The selection of PPE is dependent on a detailed risk assessment. The risk assessment should consider the work situation, the physical form of the chemical, the handling methods, and environmental factors.

OVERALLS, SAFETY SHOES, SAFETY GLASSES, GLOVES, DUST MASK. (Diagrams shown for safety glasses, gloves, goggles, and full overall suit/respirator)

  • Eye/face protection: If splashes are likely to occur, wear safety glasses with side-shields.
  • Skin and body protection: Wear suitable protective clothing.
  • Hand protection: Wear suitable gloves.
  • Respiratory protection: If determined by a risk assessment an inhalation risk exists, wear a dust mask/respirator meeting the requirements of AS/NZS 1715 and AS/NZS 1716.
  • Environmental exposure controls: Avoid creating dust. Do not allow into any sewer, on the ground or into any body of water.

9. Physical and Chemical Properties

Information on basic physical and chemical properties

  • Physical state: Solid
  • Appearance: Granules
  • Color: Brown / Tan
  • Odor: No information available.
  • Odor threshold: No information available.
Property Values Remarks • Method
pH No data available None known
pH (as aqueous solution) No data available None known
Melting point / freezing point No data available None known
Boiling point / boiling range No data available None known
Flash point No data available None known
Evaporation rate No data available None known
Flammability (solid, gas) No data available None known
Flammability Limit in Air None known
Upper flammability or explosive limits No data available
Lower flammability or explosive limits No data available
Vapor pressure No data available None known
Vapor density No data available None known
Relative density No data available None known
Water solubility Partially soluble None known
Solubility(ies) No data available None known
Partition coefficient No data available None known
Autoignition temperature No data available None known
Decomposition temperature No data available None known
Kinematic viscosity No data available None known
Dynamic viscosity No data available None known

Other information

  • No information available.

10. Stability and Reactivity

Reactivity

  • Reactivity: No information available.

Chemical stability

  • Stability: Stable under normal conditions.

Explosion data

  • Sensitivity to mechanical impact: None.
  • Sensitivity to static discharge: None.

Possibility of hazardous reactions

  • Possibility of hazardous reactions: None under normal processing.

Conditions to avoid

  • Conditions to avoid: Avoid dust generation.

Incompatible materials

  • Incompatible materials: Strong oxidizing agents.

Hazardous decomposition products

  • Hazardous decomposition products: Carbon oxides. Nitrogen oxides.

11. Toxicological Information

Acute toxicity

Information on likely routes of exposure

  • Product Information: No adverse health effects expected if the chemical is handled in accordance with this Safety Data Sheet and the chemical label. Symptoms or effects that may arise if the chemical is mishandled and overexposure occurs are:
  • Inhalation: Irritating to respiratory system.
  • Eye contact: Causes eye irritation.
  • Skin contact: Causes mild skin irritation.
  • Ingestion: May cause gastrointestinal discomfort if consumed in large amounts.
  • Symptoms: No information available.

Numerical measures of toxicity - Product Information

  • No information available.
Chemical name Oral LD50 Dermal LD50 Inhalation LC50
Ammonium nitrate = 2217 mg/kg ( Rat ) - > 88.8 mg/L ( Rat ) 4 h
Magnesium oxide = 3990 mg/kg ( Rat )
= 3870 mg/kg ( Rat )
- -
Sulfur > 3000 mg/kg ( Rat ) > 2000 mg/kg ( Rabbit ) > 9.23 mg/L ( Rat ) 4 h
Copper (II) sulfate = 300 mg/kg ( Rat ) = 1000 mg/kg ( Rabbit ) -

See section 16 for terms and abbreviations

Delayed and immediate effects as well as chronic effects from short and long-term exposure

  • Skin corrosion/irritation: Mild Irritant. Classification is based on mixture calculation methods based on component data.
  • Serious eye damage/eye irritation: Irritating to eyes. Classification is based on mixture calculation methods based on component data.
  • Respiratory or skin sensitization: No information available.
  • Germ cell mutagenicity: No information available.
  • Carcinogenicity: No information available.
  • Reproductive toxicity: No information available.
  • STOT - single exposure: No information available.
  • STOT - repeated exposure: No information available.
  • Aspiration hazard: No information available.

12. Ecological Information

Ecotoxicity

  • Ecotoxicity: Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
Chemical name Algae/aquatic plants Fish Toxicity to microorganisms Crustacea
Ammonium nitrate - LC50: 65 - 85mg/L (48h, Cyprinus carpio) - -
Sulfur - LC50: =866mg/L (96h, Brachydanio rerio)
LC50: <14mg/L (96h, Lepomis macrochirus)
LC50: >180mg/L (96h, Oncorhynchus mykiss)
- -
Copper (II) sulfate - LC50: =0.1mg/L (96h, Oncorhynchus mykiss) - EC50: 0.0058 - 0.0073mg/L (48h, Daphnia magna)

Persistence and degradability

  • Persistence and degradability: No information available.

Bioaccumulative potential

  • Bioaccumulation: No information available.
Chemical name Partition coefficient
Ammonium nitrate -3.1

Mobility

  • Mobility in soil: No information available.

Other adverse effects


13. Disposal Considerations

Waste treatment methods

  • Waste from residues/unused products: Dispose of in accordance with local regulations. Dispose of waste in accordance with environmental legislation.
  • Contaminated packaging: Dispose of in accordance with federal, state and local regulations.

14. Transport Information

ADG Not classified as Dangerous Goods by the criteria of the Australian Dangerous Goods Code (ADG Code) for transport by Road and Rail; NON-DANGEROUS GOODS.

Fertilisers meeting the descriptions of UN 2071 are not subject to to the provisions of the Australian Code for the Transport of Dangerous Goods by Road and Rail for transport by road. Dangerous Goods only when transported by air or sea.

  • UN number: 2071
  • Proper shipping name: AMMONIUM NITRATE BASED FERTILIZER
  • Hazard class: 9
  • Packing group: III
  • Hazchem code: 1Z

IATA Classified as Dangerous Goods by the criteria of the International Air Transport Association (IATA) Dangerous Goods Regulations for transport by air; DANGEROUS GOODS.

  • UN number: 2071
  • UN proper shipping name: AMMONIUM NITRATE BASED FERTILIZER
  • Transport hazard class(es): 9
  • Packing group: III

IMDG Classified as Dangerous Goods by the criteria of the International Maritime Dangerous Goods Code (IMDG Code) for transport by sea; DANGEROUS GOODS.

  • UN number: 2071
  • UN proper shipping name: AMMONIUM NITRATE BASED FERTILIZER
  • Transport hazard class(es): 9
  • Packing group: III
  • IMDG EMS Fire: F-H
  • IMDG EMS Spill: S-Q

15. Regulatory Information

Safety, health and environmental regulations/legislation specific for the substance or mixture

National regulations

Australia Classified as dangerous goods in accordance with the Australian Code for the Transport of Explosives by Road and Rail.

Fertilisers meeting the descriptions of UN 2071 are not subject to to the provisions of the Australian Code for the Transport of Dangerous Goods by Road and Rail for transport by road. Dangerous Goods only when transported by air or sea.

Classified as a hazardous chemical in accordance with the criteria of Safe Work Australia - Globally Harmonized System (GHS).

See section 8 for national exposure control parameters

  • Poisons Schedule (SUSMP): None allocated
Chemical name National pollutant inventory
Magnesium oxide - -4 10 tonne/yr Threshold category 1 fume
2000 tonne/yr Threshold category 2b fume
60000 MWH Threshold category 2b fume
20 MW Threshold category 2b fume
Copper (II) sulfate - 7758-98-7 10 tonne/yr Threshold category 1
2000 tonne/yr Threshold category 2b
60000 MWH Threshold category 2b
20 MW Threshold category 2b

International Inventories

  • AIIC: All the constituents of this material are either listed on the Australian Inventory of Chemical Substances (AICS) or have been assessed under the National Industrial Chemicals (Notification and Assessment) Act 1989 as amended.

Legend:

  • Australian Inventory of Industrial Chemicals

International Regulations

  • The Montreal Protocol on Substances that Deplete the Ozone Layer: Not applicable
  • The Stockholm Convention on Persistent Organic Pollutants: Not applicable
  • The Rotterdam Convention: Not applicable

16. Other Information

Supplier Safety Data Sheet 11/ 2019

Reason(s) For Issue: Change to Transport Information

Issuing Date: 19-Jul-2022

This Safety Data Sheet has been prepared by Ixom Operations Pty Ltd (Toxicology and SDS Services).

Revision Note: The symbol (*) in the margin of this SDS indicates that this line has been revised.

Key or legend to abbreviations and acronyms used in the safety data sheet Legend Section 8: EXPOSURE CONTROLS/PERSONAL PROTECTION

  • TWA: TWA (time-weighted average)
  • STEL: STEL (Short Term Exposure Limit)
  • Ceiling: Maximum limit value
  • *: Skin designation
  • C: Carcinogen

Key literature references and sources for data used to compile the SDS

  • EPA (Environmental Protection Agency)
  • Acute Exposure Guideline Level(s) (AEGL(s))
  • U.S. Environmental Protection Agency Federal Insecticide, Fungicide, and Rodenticide Act
  • U.S. Environmental Protection Agency High Production Volume Chemicals
  • Food Research Journal
  • Hazardous Substance Database
  • International Uniform Chemical Information Database (IUCLID)
  • Japan GHS Classification
  • Australian Industrial Chemicals Introduction Scheme (AICIS)
  • NIOSH (National Institute for Occupational Safety and Health)
  • National Library of Medicine's ChemID Plus (NLM CIP)
  • National Library of Medicine's PubMed database (NLM PUBMED)
  • National Toxicology Program (NTP)
  • New Zealand's Chemical Classification and Information Database (CCID)
  • Organization for Economic Co-operation and Development Environment, Health, and Safety Publications
  • Organization for Economic Co-operation and Development High Production Volume Chemicals Program
  • Organization for Economic Co-operation and Development Screening Information Data Set
  • RTECS (Registry of Toxic Effects of Chemical Substances)
  • World Health Organization

Disclaimer This SDS summarises to our best knowledge at the date of issue, the chemical health and safety hazards of the material and general guidance on how to safely handle the material in the workplace. Since The Supplier cannot anticipate or control the conditions under which the product may be used, each user must, prior to usage, assess and control the risks arising from its use of the material.

If clarification or further information is needed, the user should contact their Supplier representative or The Supplier at the contact details on page 1.

The Supplier's responsibility for the material as sold is subject to the terms and conditions of sale, a copy of which is available upon request.

End of Safety Data Sheet