Label - Starane Advance Label - 1L Pack - 251128
Applies to Starane Advanced | Broadleaf Herbicide
Document contents
Text extracted from the source document for accessibility and reference. Always consult the original product label above for the authoritative version.
Page 1 of 11 Starane® Advanced® Herbicide label 18th June 2021
READ SAFETY DIRECTIONS BEFORE OPENING OR USING
Starane® Advanced® HERBICIDE
ACTIVE CONSTITUENT: 333 g/L FLUROXYPYR as the methyl heptyl ester
GROUP I HERBICIDE
For the control of woody weeds in agricultural non-crop areas, commercial and industrial areas, forests, pastures and rights-of-way, as specified in the Directions for Use.
IMPORTANT: READ THE ATTACHED BOOKLET BEFORE USE.
Pack Size: 1 L
FIRST AID If poisoning occurs, contact a doctor or Poisons Information Centre. Phone: Australia 13 11 26.
[Box: EMERGENCY RESPONSE (ALL HOURS) RING FROM ANYWHERE IN AUSTRALIA (LOCAL CALL FEE ONLY)]
[Box: IN A TRANSPORT EMERGENCY ONLY DIAL 000 FOR POLICE OR FIRE BRIGADE]
SAFETY DIRECTIONS • Will irritate the eyes and skin. Avoid contact with eyes and skin. • Repeated exposure may cause allergic disorders. • When opening the container, and preparing spray and using the prepared spray, wear cotton overalls buttoned to the neck and wrist and a washable hat, (when using the spray for high volume applications with a hand gun or knapsack wear cotton overalls, over normal clothing, buttoned to the neck and wrist and a washable hat) and elbow-length PVC gloves, a face shield or goggles. • After each day's use, wash gloves, face shield or goggles and contaminated clothing. • Wash hands after use.
SAFETY DATA SHEET Additional information is listed on the Safety Data Sheet for STARANE® ADVANCED HERBICIDE which is available from Corteva Agriscience on request. Call Customer Service Toll Free on 1-800 700 096 or visit
TM ® Trademarks of Corteva Agriscience and its affiliated companies. Visit us at
Page 2 of 11 Starane® Advanced® Herbicide label 18th June 2021
RESTRAINTS: DO NOT apply to plants which may be stressed (not actively growing) due to prolonged periods of extreme cold, moisture stress (waterlogged or drought affected), poor nutrition, presence of disease, or previous herbicide treatment as reduced levels of control may result. Thorough coverage of both foliage and stems, to the point of runoff, is essential for high volume applications (see GENERAL INSTRUCTIONS; APPLICATION METHODS WOODY WEED SITUATIONS section). DO NOT spray if rain is likely within one (1) hour.
- WOODY WEED SITUATIONS Table A: High volume spraying: Dilute product with water. See GENERAL INSTRUCTIONS – APPLICATION section for APPLICATION METHOD details. Legumes present at the time of spraying will be severely damaged.
| AGRICULTURAL NON-CROP AREAS, COMMERCIAL AND INDUSTRIAL AREAS, FORESTS (INCLUDING SOFTWOOD PLANTATIONS), PASTURES AND RIGHTS-OF-WAY | |||
|---|---|---|---|
| WEEDS CONTROLLED | WEED GROWTH STAGE | RATE /100 L WATER | CRITICAL COMMENTS |
| Bathurst burr (Xanthium spinosum) | Seedlings and young plants up to 40 cm high | 45 mL | |
| Bellyache bush (Jatropha gossypiifolia) | Seedlings and young plants up to flowering | 300 mL | |
| Blue heliotrope (Heliotropium amplexicaule) | Flowering | 600 mL | |
| Black bindweed (climbing buckwheat) (Fallopia convolvulus) | Seedlings and young plants before flowering | 180 mL | |
| Blackberry nightshade (Solanum nigrum) | Seedlings and young plants up to flowering | 300 mL | |
| Bokhara clover (Melilotus albus) | Seedlings and young plants up to flowering | 300 mL | |
| Broad-leaf pepper tree (Schinus terebinthifolius) | Mature leaves, fruiting | 300 mL | Winter application only. Contact Ecosciences Precinct, Biosecurity Qld, for more information. |
| Caltrop (yellow vine) (Tribulus terrestris) (T. micrococcus) | Seedlings and young plants up to 30 cm diameter | 300 mL | |
| Cobblers pegs (Bidens pilosa) | Up to 15 cm high | 300 mL | |
| Cockspur thorn (Maclura cochinchinensis) | Up to 3 m high | 300 mL | |
| Common sensitive plant (Mimosa pudica) | Seedlings and young plants up to flowering | 300 mL | Add Uptake® Spraying Oil (see GENERAL INSTRUCTIONS; OILS and SURFACTANTS section). |
Page 3 of 11 Starane® Advanced® Herbicide label 18th June 2021
| Common sowthistle (Sonchus oleraceus) | Seedlings and young plants up to bolting | 300 mL | Add a surfactant (see GENERAL INSTRUCTIONS; OILS and SURFACTANTS section). |
|---|---|---|---|
| Creeping lantana (Lantana montevidensis) | At flowering | 300 mL | |
| Crofton weed (Ageratina adenophora) | Seedlings and young plants up to flowering | 300 mL | |
| Docks (Rumex spp.) | Seedlings and rosettes up to 30 cm high | 300 mL | |
| Flannel weed (Sida cordifolia) | Seedlings and young plants up to flowering | 300 mL | |
| Giant sensitive tree (Mimosa pigra) | Apply from mid to late summer. | 180 mL | Add Uptake® Spraying Oil (see GENERAL INSTRUCTIONS; OILS and SURFACTANTS section). |
| Hexham scent (Melilotus indicus) | Seedlings and young plants up to flowering | 300 mL | Boom spray: Starane® Advanced at 180 mL/ha + 400 mL/ha of 2,4-D amine (625 g/L) |
| Hiptage (Hiptage benghalensis) | Seedlings plants up to 1.3 m high | 300 mL | |
| Honey locust (Gleditsia triacanthos) | Seedlings and young plants up to 2 m high | 300 mL | |
| Lantana (Lantana camara) | Seedlings and regrowth 0.5 to 1.2 m high | 300 mL | Apply to actively growing plants from October to April. Some regrowth may occur particularly when treating old woody plants with sparse canopies. |
| Plants and regrowth 1.2 to 2 m high | 600 mL | ||
| Limebush (Eremocitrus glauca) | Infestations up to 1.5 m high only | 300 mL | |
| Madeira vine (Anredera cordifolia) | Apply at time of active growth. | 300 mL | |
| Milkweed (Euphorbia heterophylla) | 3 leaf to flowering | 600 mL | Repeat applications will be necessary to control subsequent germinations. |
| Mistflower (Ageratina riparia) | Seedlings and young plants up to flowering | 300 mL | |
| Mother-of-millions (Bryophyllum spp.) | Seedling and young plants before flowering | 360 mL | Add a surfactant (see GENERAL INSTRUCTIONS; OILS and SURFACTANTS section). |
| Noogoora burr (Xanthium pungens) | Seedlings and young plants up to 40 cm high | 45 mL | |
| Ochna (Ochna serrulate) | Plants up to 2 m high | 600 mL |
Page 4 of 11 Starane® Advanced® Herbicide label 18th June 2021
| Paddy’s lucerne (Sida rhombifolia) | Active growth | 300 mL | Plants which have been continually slashed or grazed over many seasons may be difficult to control and regrowth may occur. |
|---|---|---|---|
| Prickly acacia (Vachellia nilotica) | Seedling and young plants up to 2 m high that are actively growing | 450 mL | Add Uptake® Spraying Oil (see GENERAL INSTRUCTIONS; OILS and SURFACTANTS section). Consult Tropical Weeds Research Centre, Biosecurity Qld, Charters Towers for specific advice on application. |
| Scrub nettle (perennial) (Urtica incisa) | Flowering plants up to 1 m high | 300 mL | |
| Siam weed (Chromolaena odorata) | Plants up to 2 m high and up to flowering | 210 mL | |
| Sida (Sida spp.) | Seedlings and young plants up to flowering | 600 mL | |
| Silverleaf nightshade (Solanum elaeagnifolium) | From onset of flowering to early-berry set (usually spring to mid-summer) | 300 mL | To ensure maximum effect, delay application until the majority of shoots have emerged. Follow-up treatment of regrowth is critical for best control. |
| Small flowered mallow (marshmallow) (Malva parviflora) | Seedlings and young plants up to flowering | 300 mL | |
| Snakeweed (dark and light blue) (Stachytarpheta spp.) | Seedling and young plants before flowering | 450 mL | Add Uptake® Spraying Oil (see GENERAL INSTRUCTIONS; OILS and SURFACTANTS section). |
| St. John’s wort (Hypericum perforatum) | Flowering to early seed set | 300 mL | Late spring to early summer. |
| Stinking passion flower (Passiflora foetida) | Established plants and regrowth | 270 mL | |
| Wandering jew (Tradescantia albiflora) | Young plants up to and including flowering | 900 mL | Some regrowth will usually occur and will require re-treatment. |
| Wattles including; Acacia aulacocarpa, A. decora, A. harpophylla, A. leiocalyx, A. salicina | Seedling plants or regrowth 0.5 to 1.2 m high | 300 mL | Apply to actively growing plants when soil moisture is plentiful. Some regrowth may occur particularly when treating old woody plants with sparse canopies and under dry conditions. |
| Plants or regrowth 1.2 to 2 m high only | 600 mL | ||
| White lupin (Lupinus albus) | Young plants up to and including flowering | 300 mL | |
| Yellow-flowered devil’s claw (Ibicella lutea) | Seedlings and young plants up to flowering | 300 mL |
Page 5 of 11 Starane® Advanced® Herbicide label 18th June 2021
Table B: Basal bark application Dilute product with diesel or Biosafe only. See GENERAL INSTRUCTIONS – APPLICATION section for APPLICATION METHOD details.
| AGRICULTURAL NON-CROP AREAS, COMMERCIAL AND INDUSTRIAL AREAS, FORESTS (INCLUDING SOFTWOOD PLANTATIONS), PASTURES AND RIGHTS-OF-WAY | |||
|---|---|---|---|
| WEEDS CONTROLLED | WEED GROWTH STAGE | RATE /100 L OF DIESEL OR BIOSAFE¹ | CRITICAL COMMENTS |
| Broad-leaf pepper tree (Schinus terebinthifolius) | Plants up to 5 cm basal diameter | 2.1 L | |
| Calotrope (Calotropis procera) | Plants up to 3 m high and 10 cm basal diameter | 3 L | Plants should be cut as close to the ground (5 cm) as possible for reliable results. |
| Chinee apple (Ziziphus mauritiana) | Up to 15 cm basal diameter | 1.8 L | Treat circumference of stem to a height of 45 cm from the ground. Contact the Department of Agriculture and Fisheries, Qld, for further information. |
| Chinese celtis (Celtis sinensis) | Young plants up to 2 m high and 20 cm basal diameter | 2.1 L | Treat stems from ground level to where multi-stemmed trunks branch. |
| Cockspur thorn (Maclura cochinchinensis) | Up to 5 cm basal diameter | 1.2 L | |
| Giant sensitive tree (Mimosa pigra) | 1 L | Apply during active growth periods. | |
| Honey locust (Gleditsia triacanthos) | Plants up to 10 cm basal diameter | 900 mL | Treat circumference of stem to a height of 45 cm from the ground. Contact the Department of Agriculture and Fisheries, Qld, for further information. |
| Plants 10 to 20 cm basal diameter | 1.8 L | ||
| Plants >20 cm basal diameter | 3 L | ||
| Madeira vine (Anredera cordifolia) | Aerial and ground tubers | 2.1 L | Always treat vines away from the host tree as injury to the host tree may occur. |
| Mimosa bush (Vachellia farnesiana) | Up to 5 cm basal diameter | 1.8 L | |
| Ochna (Ochna serrulate) | Plants up to 2 m high and 10 cm basal diameter | 2.1 L | |
| Pond apple (Annona glabra) | Plants up to 20 cm basal diameter | 900 mL | DO NOT apply to trees growing in a body of water. Treat circumference of stem to a height of 50 cm from the ground wetting thoroughly to allow the spray mix to soak through the bark. |
Page 6 of 11 Starane® Advanced® Herbicide label 18th June 2021
| Prickly acacia (Vachellia nilotica) | Up to 10 cm basal diameter | 900 mL | |
|---|---|---|---|
| Siam weed (Chromolaena odorata) | Plants up to 2.5 m high and 10 cm basal diameter | 900 mL | |
| Sisal hemp (Agave spp.) | All growth stages | 1.8 L | Treat as an overall spray. Contact the Department of Agriculture and Fisheries, Qld, for advice to control large infestations. |
| 6 mL undiluted product per plant | Lever out centre of plant with crowbar and immediately treat the exposed cut area. |
¹ Biosafe may be used as an alternative carrier to diesel. For alternative biodiesel products, first seek advice from Corteva Agriscience.
Table C: Cut stump/ brushcutter application Dilute product with diesel or Biosafe only. See GENERAL INSTRUCTIONS – APPLICATION section for APPLICATION METHOD details.
| AGRICULTURAL NON-CROP AREAS, COMMERCIAL AND INDUSTRIAL AREAS, FORESTS (INCLUDING SOFTWOOD PLANTATIONS), PASTURES AND RIGHTS-OF-WAY | |||
|---|---|---|---|
| WEEDS CONTROLLED | WEED GROWTH STAGE | RATE /100 L OF DIESEL OR BIOSAFE¹ | CRITICAL COMMENTS |
| Calotrope (Calotropis procera) | Plants up to 3 m high and 10 cm basal diameter | 3 L | Plants should be cut as close to the ground (5 cm) as possible for reliable results. |
| Chinee apple (Ziziphus mauritiana) | Up to 15 cm basal diameter | 1.8 L | Contact the Department of Agriculture and Fisheries, Qld, for further information. |
| Giant sensitive tree (Mimosa pigra) | 1 L | Apply during active growth periods. | |
| Hiptage (Hiptage benghalensis) | Plants greater than 1.3 m high | 2 L | Plants should be cut as close to the ground (5 cm) as possible for reliable results. |
| Mimosa bush (Vachellia farnesiana) | Up to 5 cm basal diameter | 1.8 L | |
| Prickly acacia (Vachellia nilotica) | Up to 10 cm basal diameter | 900 mL | |
| Honey locust (Gleditsia triacanthos) | All plants up to and greater than 20 cm basal diameter | 3 L | Contact the Department of Agriculture and Fisheries, Qld, for further information. |
¹ Biosafe may be used as an alternative carrier to diesel. For alternative biodiesel products, first seek advice from Corteva Agriscience.
Page 7 of 11 Starane® Advanced® Herbicide label 18th June 2021
Table D: Low volume, high concentrate application Using a drench gun or gas-powered gun. See GENERAL INSTRUCTIONS – APPLICATION section for APPLICATION METHOD details.
| AGRICULTURAL NON-CROP AREAS, COMMERCIAL AND INDUSTRIAL AREAS, FORESTS (INCLUDING SOFTWOOD PLANTATIONS), PASTURES AND RIGHTS-OF-WAY | |||
|---|---|---|---|
| WEEDS CONTROLLED | WEED GROWTH STAGE | RATE /10 L water | CRITICAL COMMENTS |
| Limebush (Eremocitrus glauca) | Isolated bushes up to 1.2 m high only | 600 mL | Apply a 50 mL dose per 5 m2 of bush surface area. |
| Ochna (Ochna serrulate) | Isolated bushes up to 1 m high only | 300 mL | |
| Tree Violet (Hymenanthera dentata) | Apply from late flowering to green fruit up to 1.2 m high. | 600 mL | Apply a 50 mL dose per cubic metre of bush. |
NOT TO BE USED FOR ANY PURPOSE, OR IN ANY MANNER, CONTRARY TO THIS LABEL UNLESS AUTHORISED UNDER APPROPRIATE LEGISLATION.
WITHHOLDING PERIODS Pastures: DO NOT GRAZE TREATED PASTURES OR CUT FOR STOCK FOOD FOR 7 DAYS AFTER APPLICATION.
GENERAL INSTRUCTIONS MIXING Starane® Advanced may be mixed with water or diesel (or Biosafe). Mix only sufficient chemical for each days use and avoid storing. Mixing in water: Half fill the spray tank with water and add the required quantity of Starane® Advanced and complete filling. Agitate continuously to ensure thorough mixing before and during application. Mixing in diesel (or Biosafe): Half fill the spray tank with diesel or Biosafe and add the required quantity of Starane® Advanced. Add the remainder of the diesel or Biosafe and agitate or shake to mix contents. Tank mixtures: Wettable powder or dry flowable formulations (e.g. water dispersible granules) should be added to the spray tank first, followed by suspension concentrates (flowables), water soluble salts and then emulsifiable concentrate formulations (Starane® Advanced). Add spraying OILS and SURFACTANTS (wetters) last. (See COMPATIBILITY section for glyphosate (450 g/L) for additional instructions when mixing with glyphosate.)
OILS AND SURFACTANTS Oils: Use only Uptake® Spraying Oil at the rate of 500 mL/100 L of spray mix. Surfactants (wetters): Use a 100% concentrate non-ionic surfactant such as BS1000® at 100 mL/100 L of spray mix where required.
Page 8 of 11 Starane® Advanced® Herbicide label 18th June 2021
COMPATIBILITY Starane® Advanced is compatible with the herbicides listed. Follow any regional restrictions, and all directions and restrictions on the label, of any chemical mixed with Starane® Advanced. 2,4-D amine, Garlon® 600, glyphosate, Lontrel® Advanced, MCPA amine, MCPA LVE, metsulfuron-methyl, Tordon® 75-D and Trezac®.
Glyphosate (450 g/L) When mixing Starane® Advanced with glyphosate (450 g/L) to control both grass and broadleaf weeds, refer to the glyphosate product label for use rate recommended for grasses. DO NOT use glyphosate (450 g/L) at less than 1.2 L/ha in tank mixes with Starane® Advanced, when barnyard grass, buttongrass, crowsfoot grass, native millet and liverseed grass are the target species.
Mixing Instructions for glyphosate + Starane® Advanced + other tank-mix partners: Step 1: Fill the spray tank to 1/2 full with clean water, start and maintain agitation. Step 2: Where ammonium sulphate (crystalline or liquid form) is recommended, wash crystalline form at 0.8% w/v (800 g/100 L spray solution) through a top mesh screen into the tank OR add Liase at 2 % v/v (2 L/100 L spray solution) and mix thoroughly for several minutes. Step 3: Add glyphosate (450 g/L) and allow mixing thoroughly for several minutes. Step 4: For other tank-mix partners: Add dry flowable formulations (e.g. metsulfuron) first, followed by suspension concentrates (flowables e.g. atrazine), water soluble salts (e.g. Lontrel® Advanced). Step 5: Then add emulsifiable concentrate formulations, such as Starane® Advanced, and allow mixing thoroughly for several minutes. Step 6: Add remaining water to desired final fill level. Step 7: Add a 100% non-ionic surfactant at 0.2% v/v near the end of the filling process to minimize excessive foaming. Removing hose from tank immediately after the filling will prevent back siphoning into water source. Always maintain adequate agitation during application and use the tank load promptly.
APPLICATION METHODS AND WATER RATES WOODY WEED SITUATIONS Weeds must be actively growing to attain optimal effect. Delay the treatment of re-growth following bulldozing, slashing, burning, ploughing or a previous chemical treatment until it has at least 1 metre of new, vigorous growth.
A. High volume application Hand gun Apply the recommended mix to obtain full coverage of leaves and stems using a number 6 – 8 tip at 700 to 1500 kPa. To obtain good coverage, a spray volume of 1500 to 4000 L/ha (15 to 40 L/100 m2) is required per infested hectare. Ensure thorough coverage to the point of runoff. Knapsack and 12 volt sprayer packs Only recommended for the control of herbaceous weeds such as cobblers peg, docks and wandering jew. DO NOT use knapsacks or 12 volt sprayer packs to treat woody weeds.
B. Basal bark and cut stump application Basal bark DO NOT apply to wet stems as this can repel the diesel or Biosafe mixture. Spray or paint the recommended mixture around the base of each stem from ground level to a height of at least 30 cm from the ground, wetting the bark to the point of runoff.
Page 9 of 11 Starane® Advanced® Herbicide label 18th June 2021
Apply with a paint brush or a pressure sprayer with an appropriate lance and solid cone nozzle. If using spray equipment use low pressures (≤ 200 kPa) sufficient to form a cone of spray. Old rough bark will require more spray than smooth or young thin bark.
C: Cut stump Apply the recommended mixture liberally to the freshly cut stump immediately after cutting. Apply by spraying or painting the cut surface and sides of the stump. Best results are obtained when the stems are cut less than 15 cm above the ground.
D. Low volume, high concentrate application Drench gun or gas-powered gun Apply the recommended mixture uniformly across the foliage by applying 50 mL shots to cover 4 to 5 m2 of surface area of plant. This is approximately equivalent to 20 droplets per cm2 of the leaf surface. Use a marking agent as recommended by the equipment manufacturer to check spray coverage.
CLEANING SPRAY EQUIPMENT Rinse water should be discharged onto a designated disposal area or, if this is unavailable, onto wasteland away from desirable plants and watercourses.
Cleaning equipment after using water-based sprays: Rinsing: After using Starane® Advanced, empty the tank completely and drain the whole system. Thoroughly wash inside the spray unit using a pressure hose. Drain, and clean any filters in the tank, pump, lines, hoses and nozzles. After cleaning the tank as above, quarter fill with clean water and circulate through the pump, lines and nozzles. Drain and repeat the rinsing procedure twice. Decontamination (before spraying cotton and other sensitive crops; see PROTECTION OF CROPS, NATIVE AND OTHER NON-TARGET PLANTS): Wash the tank and rinse the system as above. Then quarter fill the tank and add an alkali detergent at 500 mL/100 L of water or the powder equivalent at 500 g/100 L and circulate throughout the system for at least 15 minutes. If using a concentrated laundry detergent use 250 g (or mL)/100 L water. Do not use chlorine based cleaners. Drain the whole system. Remove filters and nozzles and clean them separately. Finally flush the system with clean water and allow to drain.
Cleaning equipment after using diesel or Biosafe - based sprays: On completion of spraying, use a degreaser to remove traces of diesel or Biosafe from the sprayer. Rinse tank and spray through nozzles with water to remove degreaser. Then, quarter fill the tank with clean water and add an alkali detergent at 50 mL/10 L of water or the powder equivalent at 50 g/10 L of water. Shake sprayer, to circulate the washing solution throughout the sprayer, then spray the solution through the nozzles. Rinse well with clean water to remove the detergent. To clean brushes and containers, spray liberally with degreaser. Hose off with clean water and repeat using detergents as above. DO NOT use this equipment for any other purpose.
RESISTANT WEEDS WARNING GROUP I HERBICIDE Starane® Advanced Herbicide is a member of the pyridine group of herbicides. The product has a disrupters of plant cell growth mode of action. For weed resistance management the product is a Group I Herbicide.
Page 10 of 11 Starane® Advanced® Herbicide label 18th June 2021
Some naturally occurring weed biotypes resistant to the product and other Group I herbicides may exist through normal genetic variability in any weed population. The resistant individuals can eventually dominate the weed population if these herbicides are used repeatedly. These resistant weeds will not be controlled by this product or Group I herbicides. Since the occurrence of resistant weeds is difficult to detect prior to use, Corteva Agriscience Australia Pty Ltd accepts no liability for any losses that may result from the failure of this product to control resistant weeds. Strategies to minimise the risk of herbicide resistance are available. Contact your farm chemical supplier, consultant, local Department of Agriculture, or local Corteva Agriscience representative.
PROTECTION OF CROPS, NATIVE AND OTHER NON-TARGET PLANTS Susceptible crops include but are not limited to clovers, cotton, fruit, hops, lupins, ornamentals, peas, pine tree, potatoes, navy beans, safflower, shade trees, soybeans, sunflower, tobacco, tomatoes, vegetables, and vines. Starane® Advanced can be damaging to susceptible crops during both growing and dormant periods. Grasses are normally unaffected by Starane® Advanced and establish quickly after treatment. Transitory damage can occur on some species particularly those that spread by stolons such as couch grass (Cynodon dactylon), Kikuyu grass and carpet grass (Axonopus spp.). DO NOT allow spray to drift onto susceptible crops, shade trees and Pinus spp. DO NOT use under weather conditions or from spraying equipment which could be expected to cause spray to drift onto nearby susceptible plants.
PROTECTION OF LIVESTOCK DO NOT graze or cut treated crops for stock food except as specified under withholding periods. Poisonous plants may become more palatable after spraying, therefore livestock should be kept out of the area until the plants have died down. DO NOT allow stock to re-enter paddocks containing treated poisonous plants, until the plants have died down.
PROTECTION OF WILDLIFE, FISH, CRUSTACEANS AND ENVIRONMENT DO NOT contaminate streams, rivers or waterways with the chemical or used containers. Alongside waterways, treat only noxious weeds and poisonous plants.
STORAGE AND DISPOSAL Keep out of reach of children. Store in the closed, original container in a dry, cool, well-ventilated area. Do not store for prolonged periods in direct sunlight. Do not store near food, feedstuffs, fertilisers or seed. Do not re-use 1 L container. Triple-rinse containers before disposal. Add rinsings to spray tank. Do not dispose of undiluted chemicals on site. If recycling, replace cap and return clean containers to recycler or designated collection point. If not recycling, break, crush, or puncture and deliver empty packaging to an approved waste management facility. If an approved waste management facility is not available, bury the empty packaging 500 mm below the surface in a disposal pit specifically marked and set up for this purpose, clear of waterways, desirable vegetation and tree roots, in compliance with relevant local, state or territory government regulations. Do not burn empty containers or product.
Page 11 of 11 Starane® Advanced® Herbicide label 18th June 2021
SPILL AND LEAK MANAGEMENT Do not touch or walk through spilled material. Wear a face shield or goggles, overalls buttoned to neck and wrist, chemical resistant gloves and footwear. Stop leak when safe to do so. Dam area and prevent entry into waterways and drains. Small spills/leaks: Absorb with material such as sand, soil or sawdust. Collect spilled product and place in sealable container for disposal. Spill residues may be cleaned using water and detergent. Contain and absorb wash water for disposal. Absorb and collect washings and place in the same sealable container for disposal. Dam the area of large spills and report them to Corteva Agriscience Emergency Services at 1-800 370 754.
APVMA Approval No. :62287/117973
Corteva Agriscience Australia Pty Ltd 67 Albert Avenue, Chatswood, NSW 2067
CUSTOMER SERVICE TOLL FREE
TM ® Trademarks of Corteva Agriscience and its affiliated companies. © 2021 Corteva.
[Barcode for stock identification]
[drumMUSTER logo]
Hazard and precautionary statements according to classification under GHS (Globally Harmonised System of Classification and Labelling) Avoid breathing mist, vapours or spray. IF ON SKIN: Wash with plenty of soap and water. If skin irritation or rash occurs: Get medical advice/attention. Contaminated clothing should not be allowed out of the workplace.